Braun Millenium Lift Service Manual
File Name:Braun Millenium Lift Service Manual.pdf
ENTER SITE »»» DOWNLOAD PDF
CLICK HERE »»» BOOK READER
Size: 1394 KB
Type: PDF, ePub, eBook
Uploaded: 27 May 2019, 20:46
Rating: 4.6/5 from 653 votes.
tatus: AVAILABLE
Last checked: 10 Minutes ago!
eBook includes PDF, ePub and Kindle version
In order to read or download Braun Millenium Lift Service Manual ebook, you need to create a FREE account.
✔ Register a free 1 month Trial Account.
✔ Download as many books as you like (Personal use)
✔ Cancel the membership at any time if not satisfied.
✔ Join Over 80000 Happy Readers
Sincerely, THE BRAUN CORPORATION Ralph W. See Photos A and B. An adjust- ment screw is built into the platform stop block. The bridging microswitch will be deactivated if the outboard end of the platform contacts the unloading surface before. There are Flashing Codes, Solid Error Codes, and Solid Normal Operational Codes.The codes will be displayed on an LCD screen located on the lift control board inside the pump module. See the Manual Operating Instructions in the operator's manual for pump cover removal instructions. Light Penetrating Oil LPS2, General Purpose 11 oz. Inspect lift for rattles Perform all procedures listed in previous section also Platform pivot pin bearings (2) Apply Light Oil - See Lubrication Diagram Platform fold axles (2) Apply Light Oil - See Lubrication Diagram Inner roll stop (IB) lever bearings (2) FS19 Pressure unless otherwise noted.Service Bulletin 27049 Manual Backup Pump Hydraulic Pump Page 21. These items are not included with replacement pump modules. Loctite available from The Braun Corporation under part number 11522-1. Note: Rear pump shown, front pump mirror image. Page 23. Description NL915IB NL915FIB NL918IB NL918FIB Base Weldment 915R5142NW30 915F5142NW30 918R5142NW33 918F5142NW33 Cover, Pump, 2-Piece, Back-Bottom 915-0513RNPT 915-0513FNPT 915-0513RNPT 915-0513FNPT Cover, Pump, 2-Piece, Top-Front Assy. 915-0519RNPT 915-0519FNPT 915-0519RNPT. Description NL916IB NL916FIB NL917IB NL917FIB NL919IB NL919FIB Base Weldment 985R5148NW30 985F5148NW30 985R5148NW33 985F5148NW33 985R5148NW34 985F5148NW34 Cover, Pump, 2-Piece, Back-Bottom 915-0513RNPT 915-0513FNPT 915-0513RNPT 915-0513FNPT 915-0513RNPT 915-0513FNPT Cover, Pump, 2-Piece, Top-Front 915-0519RNPT. This warranty is limited to the original purchaser and does not cover defects in the motor vehicle on which it is installed, or defects in the lift caused by a defect in any part of the motor vehicle. http://elgazargroup.com/brightstar-br100r-manual.xml
braun millennium lift service manual, braun millenium lift service manual, braun millenium lift service manual, braun millenium lift service manual.
Warranty and Registration Instructions Immediately upon receiving the lift, examine the unit for any damage. Threshold Strip Switch 31221A (Qty. Platform Angle Adjustment Screws Right Must make full contact. Vertical Stop Block To raise the outboard end of platform - turn adjustment screw clockwise. See Photos A and B. An adjust- ment screw is built into the platform stop block. The bridging microswitch will be deactivated if the outboard end of the platform contacts the unloading surface before the inboard end while the. There are Flashing Codes, Solid Error Codes, and Solid Normal Operational Codes.The codes will be displayed on an LCD screen located on the lift control board inside the pump module. See the Manual Operating Instructions in the operator's manual for pump cover removal instructions. Apply Light Oil. Resecure, replace or correct as needed.Service Bulletin Manual Backup Pump Hydraulics Diagram 27049 Hydraulic Pump Page 21. Description Base Weldment Cover, Pump, 2-Piece, Back-Bottom Cover, Pump, 2-Piece, Top-Front Assy.This warranty is limited to the original purchaser and does not cover defects in the motor vehicle on which it is installed, or defects in the lift caused by a defect in any part of the motor vehicle. The skilled craftsmen at BraunAbility design and assemble the finest accessibility products available, and they always do so with the users in mind. But if problems or issues do arise, these manuals include operating instructions, installation instructions, servicing instructions, and instructions for troubleshooting, if needed. In these manuals, users can find information on terminology, components, safety, operation, installation, service, maintenance schedules, troubleshooting tips, parts numbers, and repairs. BraunAbility encourages all commercial partners to review the material contained in these manual with your sales representative or dealer before attempting operation. http://garyconnery.com/admin/images/brightsign-hd1010-manual.xml
Any questions or concerns can be addressed by your sales representative or dealer at that time. Please try again later. Please print or download one of the manuals indexed below. The expertise and service of our nationwide dealer network is just one more advantage of a BraunAbility Commercial product. This process involves a combination of online and hands-on training. BraunAbility will increase service benefits for dealers that are certified, and we also send automatic certification expiration reminds to dealer staff. Because of this level of service and expertise, product manuals should only serve as a resource for locating information on serial numbers, parts numbers, basic schematics, service intervals, and basic troubleshooting tips. Any attempts to self-service your BrauAbility lift could result in non-compliance with National Highway Traffic Safety Administration (NHTSA) requirements. Maintenance and lubrication procedures must be performed as specified by an authorized service technician.Notify the carrier at once with any claims. If you experience any issues with your BraunAbility commercial mobility lift during use, your first call should be to your local dealer. To find the contact information of the closest dealer to you, click here. NL MILLENIUM 05 Series Wheelchair pdf manual download. A broken wheelchair lift can wreck your day, weekend or trip. When your wheelchair lift stops Find great deals on eBay for Braun Lift in Lifts and Lift Chairs for Mobility Equipment. Shop with confidence. Full Size Van Lifts. BraunAbility UVL Wheelchair Lift. The UVL, or Under Vehicle Lift, Integrated manual back-up system. 109 Lee Road Suite D Braun Lift Parts Manual Under Vehicle Wheelchair Lift. Full access to doorway for all family members. Allows users to have access to driver area. Braun vista series wheelchair lift manual Instructions strap down space for 2008 FORD Wheelchair Shuttle Bus Van with a fully functional rear Braun Vista lift. https://www.informaquiz.it/petrgenis1604790/status/flotaganis18032022-1641
Bus Parts - Braun Lift Parts. World's leading marketplace. Find best value and selection for your BRAUN WHEELCHAIR LIFT MILLENNIUM SERIES MODEL l917FIB USED GOOD CONDITION 850 search on eBay. By 1975 the Braun Corporation had BraunAbility offers the following types of mobility lifts and vans: Equipped with both power and manual handicap lifts, Buy the Braun Vangater Series Wheelchair Lift and other handicap van platform lifts at Ability center. Braun Contacts. Feedback or Questions. News News Dealer News. Reports Product Manuals: Description: Description: Latest product manuals in electronic form. Visions statement examples, Example narative essay, Website terms of use sample, Jsp example form, Omina guide. Reload to refresh your session. Reload to refresh your session. When your wheelchair lift stops, panic can set in and we tend to act with emotion and sometimes over think simple solutions when you attempt to fix a broken wheelchair lift. In many cases it can be a simple fix, seat belt un-clipped, low voltage or the most common is the door full open limit switch is not activated. Below we have troubleshooting tips on what to check for when attempting to fix your broken wheelchair lift. Sometimes the solution to fix the broke wheelchair lift is very easy, sometimes it requires a certified tech to service the lift. If your hydraulic leaves you stranded you can try these troubleshooting methods to fix your broke wheelchair lift. Typically Located On Top Of Pump Cover Check to make sure the power cable has power entering the wheelchair lift, if you don't you should trace the power cable back to battery and look for damage causing loss of power. When you push deploy you should hear the solenoid clicking and releasing. If you hear it releasing and the lift is not lowering give a pull on the platform pulling it out. If you do not hearing it releasing you need to locate the cover on the side of the lift. http://www.dolciariavarone.com/images/braun-juicer-manual-4290.pdf
On one side of the lift you will see a large cover that is for the pump, typically on the opposite side will be the solenoid. Examine where the solenoid wiring connects to main lift harness, un-clip the connectors and check for excessive corrosion, if dirty clean points and clip them back together firmly. The Solenoid will have a thin tall clip that should be attached to the return spring. If the thin clip is disconnected from either the spring or solenoid post re-attach them together. Once you have them re-connected push the deploy button on the hand pendant to see if the solenoid activates. If you still have no action, it is possible the solenoid has failed and will need to be replaced. BraunAbility wheelchair lifts have drift struts. Push the stow button to raise the lift fully vertical, hit the deploy button and make sure the locks stay up allowing the platform to lower. The drift struck is a gas strut, if it's worn out the drift strut will collapse back to the lift faster then it deploys, if needed with a screw driver manually hold the strut up until the lift deploys past them. The solution would be to replace them. If the broke wheelchair lift has a seat belt, make sure its fully clipped in, wiggle connections while pushing the down button and check for lose or broke wire. Next you should locate the outboard rollstop at the end of the platform, check on the side of the platform for limit switches, remove covers if necessary. Make sure the outboard is fully activating the limit switch. Adjust if not fully engaging and test. At the opposite side of the platform is the inboard roll stop. Lift the bridge plate up so you can see the threshold plate. In the middle you will see a black bloke, this is a pressure limit switch. Push down and listen to hear the switch clicking and releasing. If you hear it clicking and releasing hold the bridge plate up and test lift. If still no activation you can remove the pressure limit switch, disconnect the switch. http://www.getfitcrew.com/wp-content/plugins/formcraft/file-upload/server/content/files/162844f2999d5e---bullet-express-meal-maker-manual.pdf
To verify this is the issue with the broke wheelchair lift you could connect the two wires on the main lift harness side to temporarily bypass the switch. If the lift operates with them temporally connected it confirms the issue. Immediately disconnect the wires and re-connect the pin connector and replace the switch. You should never operate the lift without this pressure limit switch, if you use the lift for commercial use you are not compliant and face major liability issues, if the lift is personal use you will run the risk of flipping your family member in the wheelchair off the platform from floor level. It's simply a troubleshooting technique to verify the solution without the new switch. At the end of the platform check if there is a limit switch. If so, tapp it a few times to see if it's stuck and release. You can also look to make sure it the wire harness is firmly clipped together. You will commonly see a micro limit switch or a mag switch. Check switch for proper function, replace if necessary. If the wheelchair lift is raising up a few inches and the outboard roll stop is not completely vertical activating the limit switch the lift will automatically stop. The outboard roll stop needs to be fully closed and limit switch being activated before it will travel higher. A quick solution is to load the wheelchair on backwards. When you do this you will be putthing the batteries and more weight closer to the lifting point on the wheelchair lift. The vertical arms are connected to the platform and have rams the perfrom the raising and lowering of the wheelchair lift. The strenght of the wheelchair is this area. The pararrale arms are attached to the top of the vertical arms. You will see a wire harness with limit switches. Locate the small micro limit switch and make sure the down limit is activated and the up is open. If the down is not, bend tap to adjust. Trace the wire harness back throutout the lift and look for smashed areas. cuacuonbinhduong.com/upload/files/compaq-presario-1060-manual.pdf
If you locate split of smach areas along the harness inspect to see if you have broken wires. Check in areas that have tight corners and inspect for brakes in wires, if possible wiggle wire harness in different areas while pushing the up button on the hand pendant. Continue to follow the harness all the way back to under the cover. Remove cover and continue to trace to board. You might come across points where they are junctions in the harness, this allows you to replace certain ares without replace the entire wire harness. Make sure all junctions are firmly conected and crrorsion free. If the wire harness appears to be damage free we would recommend you manual stow the wheelchair lift, put the pump cover back on and bring the lift to a certified tech. If you are not careful you can very easliy short the board out and have an expensive repair bill ahead. It looks similiar to a jack handel. Remove the jack hadel and locate the front of the wheelchair pump inside of the vehicle. On the top you will see they have instructions to follow. Locate the Pump Cover, on the front you will see a small tee post, one end of the pump handel you will have it open with a small notch in the bottom. Place the bottom of the handel with notch and insert it over the t post. Before you turn the handel you will need to lift up on the inboard roll stop resting on the lifts threshold, you only need to raise it slighly to raise the bridge plate over the stow locks. When you turn the handel clockwise you will tighten the t post and the lift wil stop. Open the t post untill the lift is at floor level and tighten back to stop lift for loading on to the wheelchair platform. Ensure it's as tight before loading on. When the wheelchair is centered on the platform, turn the t post back counter clockwise to lower to ground. When the lift is level on the ground help open the outboard roll stop if necessary. Push up on the locks resting over the outboard barrier. {-Variable.fc_1_url-
Hand Pendants Get Slammed In Doors Crimping The Wires Causing Them To Short Out. The default location you are seeing may have been pulled via your IP Address which typically is only accurate within about 30 miles. When not in use the split platform is stowed in parallel to the vehicle’s sides, leaving an unobstructed view and good access. With a handheld control you can stow or retrieve your wheelchair in 30 seconds. Page Count: 32 Millennium. Public Use Wheelchair Lifts. Series 05. DOT — Public Use LiftRead manualFailure to do soBraun NL Series. International Corporate Hdqrs: P.O. Box 310 Winamac, IN 46996 USAWe at The Braun Corporation wish to express our fullest appreciationWith you in mind, our skilled craftsmen have designed andThis manual provides service-related material. Refer to the FMVSS No. 403. Quick Reference Installation Sheet for installation instructions, operating instructionsSincerely,Chief Executive Of?cer. Warranty and Registration Instructions. Immediately upon receiving the lift, examine theSeries No. Pump Code. Model No. Serial No. Cylinder CodeThe sales representative must process one of theThe warranty is provided on the back cover of this manual. The warranty cards must be processed toRecord the information in the spaceThis information must be provided when ?lingThe Braun Corporation. Model No.Series No.Date of ManufactureTroubleshooting and Maintenance. Lift Terminology. 2. Switch and Sensor Locations. 3. Certification Checklist Diagnostic Procedures. 4. Platform Fold Pressure Adjustment. 5. Outer Barrier Fold Pressure Adjustment. 5. Platform Angle Adjustment. 6-7. Platform Stop Blocks. 7. Platform Floor Level Adjustment. 8. Bridging Microswitch Adjustment. 9. LCD Lift Codes. 10-11. Lubrication Diagram. 12. Maintenance and Lubrication Schedule.. 13-15. Notes. 16. Lift Electrical Schematic. 17. Lift Wiring Diagram. 18Hydraulic Schematic. 19. Hydraulics Parts List.. 20. Hydraulics Diagram.. 21Pump ModuleExploded View. 26. Repair Parts List. https://creationstationdance.com/wp-content/plugins/formcraft/file-upload/server/content/files/162844f5a84116---bulldozer-user-manual.pdf
27. Notes. 28Hand-Held. Pendant. ControlVisual. Threshold. WarningMain Cylinders (2)Threshold. Warning. Unfold Assist Compression Springs (2). Adjustable Quiet-Ride Stow Blocks (2). Platform Lights. Opposite Pump Side Vertical Arm. Vertical Arm Covers (4). Pump. ModuleThreshold. Plate. Handrails (2). Base. Inner Roll Stop. Bottom Parallel. Arms (2). Rotating Pivot. Slide Arms (2). Platform Pivot Arms (2). Platform. Pump Side Vertical Arm. Outer Barrier CylinderPlatform Side Plates (2). Outer BarrierOuter Barrier Latch. Inboard. Left. InboardRight. Outboard. FrontNL917-05-003.ai. RearOutboardPressure SwitchMicroswitch Assy.SensorOuter Barrier Latched. MagnetMagnetic SensorMagnetic SensorLeft. Right. Outer Barrier Raised. MagnetNL917-05-033.aiThe following operations and conditions must be functionally verified in order for the lift to be FMVSSVerify the threshold strip switch connectors are connected (see illustration on Page 3). Replace the threshold strip switch. Reinstall the threshold warning platePlatform Fold. Adjustment. Allen Screw. Note: Secure adjustmentOuter Barrier Fold Pressure AdjustmentDO NOT turn the adjustment screw beyond thisOuter Barrier. Fold Adjustment. Allen ScrewAdjusting the platform angle based on theMillennium “NL” Series. Figure C. Unfold the lift and visually examine theThe outboardMillennium “NL” Series. The platform angle should be adjusted soCentury “NCL” Series. The platform angle must be adjusted soWedgesInboard. Century “NCL” Series. Allen screws are provided on each side ofFigure DToe mustPage 6. BarrierWedges. OutboardAdjustment Allen screws areNote: RWK adjustment screws. To raise the outboard endTo lower the outboard endPlatform Angle. Adjustment Screws. Adjustment Screw. Allen HeadTurnPlatform Stop Blocks. Wrong. Vertical Stop. Arm BlockVertical. Arm. When adjusting platformStop. BlockPower switch On.Position platform such that:Note: Use hand pump to position platform at proper posi-Set button. www.easyhairstyler.com/tmp/phpu2CJCz' to '/home/www/happyhair/easyhairstyler.com/htdocs/www/img/files/car-manual-vs-automatic.pdf
If repeating procedures fails - referMillennium: Check latch). Page 8Adjustment Screw. Bridging MicroswitchPhotos A and B. An adjustment screw is built into theThe bridging microswitch willThe deactivated bridging microswitch interrupts power toInboard Vertical. Edge of Vertical Arm. Stop Block. Switch. Activation Lever. Caution: This adjustment isEnsure the platform is notJDS between the stop blocksPage 9Remember they are notThese numbers will only stay on theIt is important to be looking at the screen when trying to get the liftIf nothing is found, the next step is to determine if that sensor is sending a signal to the board.You should then check the harness or try another magnetIE: Outboard Barrier is closed “72” will appear on the screen and also 8VPage 10Listed below are codes that the lift controller outputsThe codes will be displayedSee the Manual Operating. Instructions in the operator's manual for pump coverPage 11Lubrication Diagram. Lift-Tite LatchesPivot Pins (8)Rotating Pivot Slide. Arm UHMW Slide (1)Pivot PointsUHMW Bearings (2) DE. Outer Barrier Hinge. Pivot Points (2)Slide Arm Pivot PinsOuter Barrier Latch LeverLO - Light Oil. DE - Door-Ease. LG - Light Grease. Page 12Specified (recommended). Lubricant. Available. Amount Penetrating Oil. Aerosol Can. Stainless Stick. Door-Ease 1.68 oz. Style (tube). Stick (tube). Light Grease. Lubriplate 14 oz. Can. NL917-05-003.ai. Braun. Part No.Proper maintenance is necessary to ensure safe,Inspecting the lift for any wear,The maintenance and lubrication procedures specifiedBraun dual parallel arm lifts are equipped with hardened pins and self-lubricating bushings to decreaseWhen servicing the lift at the recommended intervals,LPS2 General Purpose Penetrating. Oil is recommended where Light Oil is called out. Use of improper lubricants can attract dirt or otherLift components requiring grease are lubricated duringThe Braun Corporation (part numbers provided above). All listed inspection, lubrication and maintenanceThese intervalsLifts exposed to severeMaintenance Indicator: The Lift Ready green LEDThe blinking LED will not affectOnce the lift has been serviced, fully stow the lift. OnceDiscontinue lift use immediately if maintenance andContact your sales representative or call TheOuter barrier hinge pivot points (2). Apply Light Oil - See Lubrication Diagram. Outer barrier latch lever pivot points Apply Light Oil - See Lubrication DiagramResecure, replace defective parts or otherwiseInspect outer barrier for proper operation Correct or replace defective parts.Page 13Inspect lift for wear, damage or any abnormalCorrect as needed. Inspect lift for rattles. Correct as needed. Perform all procedures listed in previous section alsoPage 14. Platform pivot pin bearings (2) Apply Light Oil - See Lubrication Diagram. Inner roll stop (IB) lever bearings (2). Inner roll stop (IB) lever slot (2). Rotating pivot slide arm pivot pins (2). Apply Light Oil - See Lubrication DiagramParallel arm pivot bearings (16). Handrail pivot pin bearings (4). Hydraulic cylinder bushings (8). Apply Light Oil - See Lubrication DiagramInspect inner roll stop (IB) for:Resecure, replace or correct as needed. See. Platform Angle Instructions and Microswitch Adjustment Instructions. Inspect handrail components for wear or damage,Replace defective parts.Resecure, replace or adjust as needed. See. Microswitch Adjustment Instructions. Inspect external snap rings: Resecure or replace if needed. Inspect platform fold axles and bearings for wear orReplace defective parts and resecure as needed. Apply Light Oil. Realign towers and vertical arms. Lubricate orRemove pump module cover and inspect: Resecure, replace or correct as needed. Perform all procedures listed in previous section also. Inspect cotter pins on platform pivot pin (2). Resecure, replace or correct as needed. Hydraulic Fluid (Pump) - Check level. Note: FluidInspect the hydraulic system (cylinder, hoses, fittings, seals, etc.) for leaks if fluid level is low.Inspect cylinders, fittings and hydraulic connectionsTighten, repair or replace if needed. Inspect outer barrier cylinder hose assembly (hose,Replace if needed. Inspect parallel arm pivot pin mounting bolts (8). Tighten or replace if needed. Inspect platform pivot pin, bushings and verticalReplace defective parts and resecure as needed. Apply Light Grease during reassembly procedures.Replace if needed. Inspect gas springs (cylinders) for wear or damage,Tighten, replace or correct as needed. Inspect rotating pivot slide arm UHMW slide bearings (buttons - 2) and UHMW slide (1). Apply Door-Ease or replace if needed. See Lubrication Diagram.Inspect vertical arm plastic covers. Inspect power cable Decals and Antiskid. Replace decals if worn, missing or illegible. Replace antiskid if worn or missing. Check to see that the lift is securely anchored toConsecutive Repeat all previously listed inspection, lubrication and maintenance procedures at 750 cycleIntervals. Page 15Page 16Sc t E ldLift Wiring DiagramMicroswitchCircuit SentryDown. Dual ReliefBack. PlatePower CableLatched SensorLead WireDual. ReliefStud. Connects to. Vehicle BatteryRaised SensorPump. Pump GroundDetail at left shows two differentFuse. Pump Module. Power FeedHarness. Light. BeeperPosition. Sensor. Floor Level. Memory Set. Push ButtonBoxMicroswitchSwitch. Stow Interlock (-). MicroswitchControl. ModuleConnectionSwitchPressure Switch. Bridging. Valve. Orifice. Lifting. Relief Valve. Down. Secondary. ValvePump. CylinderFolding. Outer Barrier. Cylinder. Pump Side. CylinderFixed Displacement. Pump MotorSymbol. Hydraulic PortSolenoid Valve. Backup Pump. Pressure Compensated. Flow Control. Single Acting Cylinder. Check Valve. Filter Screen. Unfold Orifice. If you aren't experienced in the kitchen or have never owned a food processor before, get some help with this item to learn its abilities. Once you get the hang of it you will love all it can do. It will replace several items in my kitchen and that is a huge plus so I feel it is well worth its price. See more QueenOfInterneShopping, October 15, 2018 Spark Reviewer - received free product Top 250 contributor 0 0 Average Rating: ( 3.0 ) out of 5 stars works good but beware lots of parts so this food processor is good and has good power but my only complaint is that there are so many parts.Glad it works well but not sure if i would recommend. Ask a question Ask a question If you would like to share feedback with us about pricing, delivery or other customer service issues, please contact customer service directly.In some part of the description is stated that it has 700watts, but later it says 400. Product warranty: 1 Years See details Warranty Information: 3 Year Limited Already purchased your product. A Walmart Protection Plan can be added within 30 days of purchase. Click here to add a Plan. All Rights Reserved. To ensure we are able to help you as best we can, please include your reference number: Feedback Thank you for signing up. You will receive an email shortly at: Here at Walmart.com, we are committed to protecting your privacy. Your email address will never be sold or distributed to a third party for any reason. If you need immediate assistance, please contact Customer Care. Thank you Your feedback helps us make Walmart shopping better for millions of customers. OK Thank you! Your feedback helps us make Walmart shopping better for millions of customers. Sorry. We’re having technical issues, but we’ll be back in a flash. Done. 2 shows the functional blocks of the control PWB, which is composed of 3 blocks. 5) Flash Memory Controller (1) SCE209 IA(CX20438) MEMORY(SRAM) The SCE209 includes a flash memory controller that supports NOR, NAND, and Serial NAND-type flash memory. The supported size of NORtype memory is up to 1 MB and the supported size of NAND-type memory is unlimited. (2) FLASH 6) Stepper Motor Control Eight outputs are provided to external current drivers: four to the scanner motor and four to the printer motor. The stepping patterns are programmable and selectable line times are supported. A timeout circuit controls the power control of the motors. Devices are connected to the bus to control the whole unit. 8) Bi-level Resolution Conversion 1) SCE209 (IC3): pin-176 QFP (FAX CONTROLLER) One independent programmable bi-level 1D-resolution conversion block is provided to perform expansion or reduction on the T.4 decompressed data and scan image data. Image expansion can be programmed up to 200 and reduction down to 33. Vertical line ORing and data output bit order reversal is also provided. 1 chip fax engine has Internal Integrated Analog (20438) and Internal memory (SRAM: 32kbit). 2) SST39VF020P (IC1): pin-32 TSOP (FLASH) FLASH of 2Mbit equipped with software for the main CPU. 9) Printer IF 3) MSM51V4800E (IC2): pin-28 SOJ (DRAM) The Printer Interface provides a standard connection between the SCE209 and a thermal printhead to support thermal printing or thermal transfer. The thermal printer interface consists of programmable data, latch, clock, and up to four strobe signals. Programmable timing supports traditional thermal printers, as well as the latchless split mode printers, and line lengths of up to 2048 pixels. Line times from 5 ms to 40 ms are supported. External terminating resistors must be supplied; the values are determined by the specific printhead selected. As an option, plain paper inkjet printing can be supported. The CPU connects to other internal functions over an 8-bit data bus and 24-bit address bus and dedicated control lines. The 24-bit external address bus, 8-bit data bus, control, status and decoded chip select signals support connection to external ROM, SRAM, DRAM, and FLASH memory. 10) TPH Hardware Timer The TPH hardware timer provides a 500 ms timer that can be re-triggered or reset. 11) Scanner and Video Control Five programmable control and timing signals support common CCD and CIS scanners. The video control function provides signals for controlling the scanner and for processing its video output. Three programmable control signals (START, CLK1n, and CLK2) provide timing related to line and pixel timing. These are programmable with regard to start time, relative delay and pulse width. These signals provide a per pixel period, or per line period, timing with programmable polarity control for each signal. 2) DRAM Controller The CX06835 includes a DRAM controller with signal and page mode access support which supports fast, normal, or slow refresh time. DRAM memory space is provided in one block up to 4 MB. A maximum of 4 MB of DRAM is supported. This space has a programmble size and starting address. Refresh is performed automatically and is supported in standby mode. CAS and RAS signal support is provided for one-DRAM banks for both 4-bit and 8-bit organizations. Corrections are provided on either an 8-pixel group or are applied separately to each pixel. Dark level correction and gamma correction are also provied. The CX06835 includes an 8 x 8 dither table, which is programmable and stored internally (8-bit per table entry). The table is arranged in a matrix of 8 rows by 8 columns. The conversion ratio of the multi-level Resolution Conversion is fixed to B4-A4 conversion. This control signal is also provied as an output on the PWRDWNn pin.